Last time I walked through creating a sparse disk image using
dd and cp --sparse=always. OK, we have a disk
image. Now what?
Normally it would suffice to just set up a loop device and then mount, but this disk image doesn't just contain a filesystem. It has 4 partitions each with their own filesystem. This means in order to mount one of the filesystems we have to take a few extra steps.
There is an easy and a hard way to do this. I'll start with the hard way..
The Hard Way
To manually mount a particular partition on the disk we need to find a little information about where the partition is located on the disk. We need to use
fdisk to find the offsets of the start and end of the partition.
dustymabe@media: mnt>sudo fdisk -l /mnt/lenovo.img Disk /mnt/lenovo.img: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xf82e2761 Device Boot Start End Blocks Id System /mnt/lenovo.img1 * 2048 411647 204800 7 HPFS/NTFS/exFAT /mnt/lenovo.img2 411648 884611071 442099712 7 HPFS/NTFS/exFAT /mnt/lenovo.img3 884611072 946051071 30720000 7 HPFS/NTFS/exFAT /mnt/lenovo.img4 946051072 976361471 15155200 12 Compaq diagnostics
From the
fdisk output we can see that the second
partition starts at 411648 sectors times 512 bytes (210763776 bytes)
into the disk image. We can also see that the partition ends at
884611071 sectors times 512 bytes (452920868352 bytes). This means
that the size of the partition is 452920868352 - 210763776 =
452710104576 bytes.
We can use this information to set up a loop device using
losetup like so:
dustymabe@media: >sudo losetup -v -f -o 210763776 --sizelimit 452710104576 /mnt/lenovo.img dustymabe@media: > dustymabe@media: >losetup -a /dev/loop0: []: (/mnt/lenovo.img), offset 210763776, sizelimit 452710104576 dustymabe@media: > dustymabe@media: >sudo blkid /dev/loop0 /dev/loop0: LABEL="Windows7_OS" UUID="7C64B5C764B58504" TYPE="ntfs"
Finally, the loop device can be mounted just like a normal block device:
dustymabe@media: >sudo mount -o ro /dev/loop0 ~/Desktop/mount/ dustymabe@media: >ls ~/Desktop/mount/Users All Users Default Default User desktop.ini dustymabe Public
The Easy Way
You can use
partx to probe a disk image and detect all
partitions. You can also have partx tell the kernel about
all partitions and add devices for each partition. An example of this
is shown below:
dustymabe@media: >sudo losetup -v -f /mnt/lenovo.img dustymabe@media: >sudo losetup -a /dev/loop0: [2145]:12 (/mnt/lenovo.img) dustymabe@media: > dustymabe@media: >sudo partx --show /dev/loop0 [sudo] password for dustymabe: NR START END SECTORS SIZE NAME UUID 1 2048 411647 409600 200M 2 411648 884611071 884199424 421.6G 3 884611072 946051071 61440000 29.3G 4 946051072 976361471 30310400 14.5G dustymabe@media: > dustymabe@media: >sudo partx -v --add /dev/loop0 partition: none, disk: /dev/loop0, lower: 0, upper: 0 /dev/loop0: partition table type 'dos' detected /dev/loop0: partition #1 added /dev/loop0: partition #2 added /dev/loop0: partition #3 added /dev/loop0: partition #4 added dustymabe@media: > dustymabe@media: > dustymabe@media: >sudo blkid /dev/loop0* /dev/loop0p1: LABEL="SYSTEM_DRV" UUID="0840B6DE40B6D224" TYPE="ntfs" /dev/loop0p2: LABEL="Windows7_OS" UUID="7C64B5C764B58504" TYPE="ntfs" /dev/loop0p3: LABEL="LENOVO" UUID="7652C00A52BFCCDD" TYPE="ntfs" /dev/loop0p4: LABEL="LENOVO_PART" UUID="983479C03479A244" TYPE="ntfs"
Now you can directly mount
/dev/loop0p2 just as we did
before.
dustymabe@media: >sudo mount -o ro /dev/loop0p2 ~/Desktop/mount/ dustymabe@media: >ls ~/Desktop/mount/Users/ All Users Default Default User desktop.ini dustymabe Public dustymabe@media: >
There ya go.. Two ways to mount partitions within a disk image. If I get a chance I'll go over a third using some free tools from the virt community.
Dusty
References: http://www.novell.com/communities/node/7066/accessing-file-systems-disk-block-image-files
